Shindaiwa EC7600 Betreibershandbuch Seite 12
- Seite / 84
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
12
Figure 20
Back off tension screw another 4-5 turns
so that adequate clearance is achieved
where the tension screw contacts the
mount when the mount is turned over.
See Figure 17.
2.
6mm Socket-
Head Bolts
Figure 21
Reversing cutting head for flush cutting operations
WARNING!
Before performing any work
on the cut-off saw, make sure the
engine is stopped and the ignition
switch is OFF.
NOTE:
For units equipped with a water kit, loosen
the (2) water nozzles and disconnect the
main water line from the double nozzle.
Remove the cutting wheel (Refer to
Section Mounting the Cut-off Wheel).
Using a Phillips screwdriver, loosen the
tension screw until the tension indicator
is all the way to the front of the scale.
See Figure 16.
1.
Figure 16
Tension Screw
Tension
Indicator
Remove Cutting Wheel
Loosen Two
Bolts
Using a 6mm hex wrench, remove the
two belt guard bolts and slide the belt
guard forward to remove. See Figure 18.
3.
Figure 17
Mount
Tension Screw
Figure 19
Making sure that the drive belt is fully
engaged in the drive pulleys, slide the
belt cover on and install the two socket-
head bolts into the left-hand side of the
mounting surface only until the bolts
bottom on the belt cover. See Figure 20.
5.
Belt Guard
Figure 18
Remove the blade mount from the
mounting surface and rotate the blade
mount 180
0
, then remount to the right
hand side of mounting surface
. See
Figure 19.
4.
6mm Socket-
Head Bolts
Operating (continued)
Adjust the tension screw until the
tension indicator is in the middle of the
scale. See Figure 21.
6.
Tighten the two mounting bolts securely.
Reconnect the main water line, adjust
and retighten water nozzles (if equipped
with a water kit).
Reinstall the cutting wheel. Back off
tension screw another 4-5 turns so that
adequate clearance is achieved where the
tension screw contacts the mount when the
mount is turned over. See Figure 17.
7.
8.
9.
- EC7500/EC7600 1
- ENGINE CUTOFF SAW 1
- Introduction 2
- Attention Statements 2
- Contents 2
- Safety Precautions 3
- Figure 1 4
- Figure 2 4
- Figure 3 4
- Safety Labels 5
- Unit Description 6
- Specifications 6
- Prior to assembly 7
- Mounting the Cut-off Wheel 7
- Mixing fuel 8
- Filling the fuel tank 8
- Starting a cold engine 9
- If the engine doesn’t start 9
- Starting a warm engine 9
- Stopping the Engine 10
- Wet or Dry Operation 11
- Adjusting Wheel Guard Angle 11
- Operating (continued) 12
- EC7500.48 13
- Cleaning the Air Cleaner 13
- Figure 24 14
- Figure 23 14
- Adjusting Belt Tension 15
- Replacing the Drive Belt 15
- Checking the Cut-off Wheel 15
- EC7500.42 16
- Replacing the Cut-off Wheel 16
- Checking the Fuel Filter 16
- Spark Arrester Maintenance 17
- Troubleshooting Guide 18
- DECLARATION 19
- CONFORMITY 19
- DÉCOUPEUSE THERMIQUE 23
- Mises en garde 24
- Table des matières 24
- Consignes de sécurité 25
- Consignes de sécurité (suite) 26
- Étiquettes de sécurité 27
- Description de l’appareil 28
- Caractéristiques techniques 28
- Avant l’assemblage 29
- Exemples de quantités de 30
- Démarrage d’un moteur froid 31
- Si le moteur ne démarre pas 31
- Démarrage d’un moteur chaud 31
- Arrêt du moteur 32
- Démarrage du moteur (suite) 32
- Fonctionnement 33
- Fonctionnement (suite) 34
- Nettoyage du filtre à air 35
- Figure 25 37
- Figure 26 37
- Figure 27 37
- Figure 28 37
- AVERTISSEMENT ! 38
- Entretien du pare-etincelles 39
- Guide de dépannage 40
- DÉCLARATION 41
- CONFORMITÉ 41
- REMARQUES : 42
- MOTOTRONCATRICE 45
- Sommario 46
- Messaggi informativi 46
- Introduzione 46
- Precauzioni di sicurezza 47
- Etichette di sicurezza 49
- Descrizione dell’attrezzo 50
- Specifiche tecniche 50
- Montaggio del disco da taglio 51
- Prima dell’assemblaggio 51
- Rifornimento del serbatoio 52
- Avviamento del motore a caldo 53
- Se il motore non si avvia 53
- Avviamento del motore (cont.) 54
- Arresto del motore 54
- Funzionamento 55
- Funzionamento (cont.) 56
- Pulizia del filtro dell’aria 57
- Figura 23 58
- Figura 24 58
- Controllo del disco da taglio 59
- AVVERTENZA! 60
- Figura 32 61
- Figura 33 61
- Risoluzione dei problemi 62
- DICHIARAZIONE 63
- DI CONFORMITÀ 63
- Italiano 64
- TRENNSCHLEIFER 65
- Einführung 66
- Wichtige Hinweise 66
- Vorsichtsmaßnahmen 67
- Abbildung 1 68
- Abbildung 2 68
- Arbeiten Sie immer unter 68
- Brusthöhe 68
- Abbildung 3 68
- Sicherheitsaufkleber 69
- Technische Daten 70
- Gerätebeschreibung 70
- Vor dem Zusammenbau 71
- Montieren der Trennscheibe 71
- Beispiele für 72
- Kaltstart des Motors 73
- Warmstart des Motors 73
- Ausschalten des Motors 74
- Trennschleifen 75
- Nass- oder Trockenbetrieb 75
- Betrieb (Fortsetzung) 76
- Reinigen des Luftfilters 77
- Abbildung 23 78
- Abbildung 24 78
- Einstellen der Riemenspannung 79
- Überprüfen der Trennscheibe 79
- Auswechseln der Trennscheibe 80
- Schmieren des Kupplungslagers 81
- Fehlerbehebung 82
- KONFORMITÄTSERKLÄRUNG 83
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.085 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern