Shindaiwa T242X/EVC Betreibershandbuch

SHINDAIWA OWNER’S/OPERATOR’S MANUALT242X TRIMMERWARNING!Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself

10 WARNING! Alternative fuels, such as E15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting Shindaiwa requirements are NOT approved for use

11 After use• DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel stor-age container.

12XST013Starting the Engine 4. While holding the outer tube firmly with left hand. Use your other hand to slowly pull the recoil starter handle until

13NEVER operate the unit with the cutting attachment shield or other protective devices removed!WARNING!A cutting attachment shield or other protectiv

14Hold the trimmer so the trimmer head is angled slightly into the area to be cut. To ensure maximum trimmer-line service life, cut only with the tip

15Using a bladeBrushcutter Shoulder StrapA shoulder strap provides additional protection against blade thrust. In addition, a shoulder strap gives si

16MaintenanceWARNING!Before performing any maintenance, repair, or cleaning work on the unit, make sure the engine and cutting attachment are complete

17spark plug gap--all modelsEvery 10 to 15 hours of operation: Remove and clean the spark plug. Adjust the spark plug electrode gap 0.6 mm to (0.02

18CAUTION!Make sure you do not pierce the fuel line with the end of the hooked wire. The line is delicate and can be damaged easily.Figure 29Filter

19135-hour MaintenanceEvery 135 hours of operation, remove and clean the muffler.WARNING!Never operate this trimmer with a damaged or missing mufer or

2Shindaiwa hand held power equipment has been designed and built to deliver superior performance and reliability without compromise to quality, comfor

20Carburetor AdjustmentEngine Break-InNew engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can

21 Remove the spark plug and pour about 1/4 oz. of engine oil into the cylinder through the spark plug hole. Slowly pull the recoil starter 2 or 3 t

22Troubleshooting GuideVaporlock.Engine hot/heat soaked.Low fuel quality.Let cool completely and restart.Refi ll with fresh, clean unleaded gasoline wi

23Is the engine overheating?Engine is rough at all speeds. May also have black smoke and/or unburned fuel at the exhaust.Operator is overworking the u

24ADDITIONAL PROBLEMSPoor acceleration.Clogged air fi lter.Clogged fuel fi lter.Lean fuel/air mixture.Idle speed set too low.Ignition switch turned off.

25SHINDAIWA LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010ECHO, INC’S RESPONSIBILITYECHO Incorporated’s (ECHO, INC

26PURCHASED REPAIR PARTS AND ACCESSORIES• 90-day all applicationsATTENTION ENGINE POWERED PRODUCT OWNERSThis Shindaiwa engine powered product is a qu

27 ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENTFOR ECHO AND SHINDAIWA BRANDSThe Environmental Protection Agency (EPA) and the California Air

ECHO Incorporated.400 Oakwood RoadLake Zurich, IL 60047-1564 U.S.A.Telephone: 1-877-986-7783Fax: 1-847-540-8416www.shindaiwa.com Yamabiko Corporation

3WARNING!Never operate power equipment of any kind if you are tired or if you are under the inuence of alcohol, drugs, medication or any other subs

4Figure 1Safety LabelsIMPORTANT!Safety and Operation Information Labels: Make sure all information labels are undamaged and readable. Immediately repl

5Be Aware of the Working EnvironmentAvoid long-term operation in very hot or very cold weather.Make sure bystanders or observers outside the 15 meter

6SpecicationsModel T242XEngine Type 2-stroke, single cylinder, air cooled, gasoline engineDry Weight (less attachment) 5.3 kg/11.7 lb.Dimensions (L x

7Prior to AssemblyBefore assembling, make sure you have all the components required for a complete unit and inspect unit and components for any damage

8WARNING!NEVER use this machine without sub-shield when using a trimmer head.Cutting Attachment Shield1. Insert the cutting attachment shield betwee

9Assembly (continued)1. Align the notch in blade holder (A) with the notch in the gear case flange. Lock the holder and output shaft by inserting a h